[China Glass Net] There are three general methods for mounting and fixing the wall glass decorative mirrors, namely, the nailing method, the sticking method and the inlay method. The following is a detailed description of the whole house of the glass. 1. Nailing This method is to fix the wall glass decorative mirror to the wall (or cylinder, top) base layer with screws. Specific steps are as follows: (1) The wall treatment wall requires flatness, no bulge, unevenness, and if the wall is flat, it can be directly used for installation; otherwise, cement mortar can be used (if the amount of moisture-proof powder can be added is better), scraping Level it again. (2) Drilling holes Each wall glass decorative mirror needs to be drilled with four mounting fixing holes. The hole positions should be evenly distributed, and should not be too close to the edge of the mirror to prevent cracking. The fixed wall glass decorative mirrors currently on the market have already been installed with mounting holes, and the non-shaped glass mirrors can be punched at professional processing points. Install the glass mirror on the wall, then place the decorative mirror on the wall, mark it through the hole in the glass mirror, move it in the corresponding hole on the wall, use the drill or The hammer is drilled at the location marked on the wall. The hole diameter should be determined according to the size of the selected screw. Generally, it is preferably less than 3 mm in diameter of the screw end. (3) Laying the cushioning material In order to prevent the wall glass decorative mirror from being damaged due to the unevenness of the base layer, a cushioning material should be applied between the mirror and the wall surface. The lining heat material is preferably an elastic body of thin felt or sponge board, which can be 2~3 mm thick, and is fixed on the wall with a white glue. The size of the cushion material is preferably 10-15 mm smaller than the glass, so that the mirror is suitable for the mirror. After installation, seal the perimeter with caulk. (4) Before installing the glass mirror, a layer of kraft paper protective layer should be attached to the back of the glass mirror. The specific method is to first apply a layer of milky white glue on the back of the mirror, then stick a piece of kraft paper on the back of the mirror, and then use a plastic plate to smooth it. Pre-bury the plastic expansion bolts in the holes in the wall, put the mirrors in place for the holes, fix them with screws, and tighten them diagonally. It is better to use a glass mirror without shaking. (5) After the closed glass is fixed and installed, in order to prevent moisture from invading the back of the mirror and affecting the service life and quality of the mirror, the gap between the mirror and the wall should be embedded with the caulking paste. 2. Paste method The glass mirror is directly attached to the base layer of the wall by using an adhesive with a high bonding strength. This method is suitable for the installation of wall surfaces within 1 square meter. If the mirror size is large, or the ceiling-mounted mirror, it is better to use a combination of sticking and nailing to ensure that when the mirror is broken, it will not fall and hurt people. The specific method of pasting is as follows: clean the back of the mirror to remove dust and sand. Apply a layer of kraft paper as a protective layer on the back of the mirror. Then apply the multi-purpose glue on the kraft paper on the back of the mirror and the base surface of the wall. When the rubber surface is not sticky, attach the glass mirror directly to the wall surface according to the position line that has been pre-applied. Press the mirror with your hand to make it adhere to the wall and pay attention to the sticking at the corners. When the mirror is stuck, seal the perimeter with caulking. It should be noted that before the mirror is attached, the wall surface should be flat, otherwise it should be smoothed with cement mortar. In addition, the multifunctional glue should not be applied directly to the back of the mirror to prevent it from corroding the coating of the mirror. In addition, in addition to the use of multi-functional adhesive as an adhesive, you can also use a double-sided tape to attach the mirror. This double-sided tape is made of high-strength adhesive on both sides of the sponge board, about 2-3 mm thick, and has certain elasticity. When used, cut into 5-10 cm wide strips, first remove the protective paper from one side, paste it on the base layer of the wall, and press the hand tightly to make the mirror and the tape stick. The caulking paste is then used to enclose the perimeter of the mirror. 3. Embedded method The inlay method is to use stainless steel, aluminum alloy or wood line as the frame of the glass mirror. The frame is fixed with the wall base layer by the nailing method, and then the glass mirror is embedded in the frame. This method is suitable for the installation and fixing of large-area glass mirrors. The specific method of the embedded pressure is as follows: firstly, according to the size of the frame, the bullet line, the hole, and the eye. Fix the lower frame bead according to the elastic line. The spacing of the nails should be 10-15 cm to increase the strength of the bottom support. The blanket is then applied to the substrate with a milky white gel. Then insert the mirror into the bead of the lower frame, and align it with the wall surface, and install the upper frame bead and the side frame bead. It should be noted that when fixing the wood bead, it is better to use a nail gun of 20~25mm to fix it, avoiding the use of ordinary round nails to prevent the mirror from being broken when the nail is pressed. In addition, it can also be set without nails. The specific method is to first use a wooden lining to clamp the glass mirror, and then use a multi-purpose glue to stick the stainless steel or aluminum alloy bead on the wooden lining, and then between the bead and the glass mirror. Seal the glass glue at the corner. Leather Casual Shoes,Leather Sport Shoes Mens,Fashion Sport Shoes Leather,Mens Casual Leather Sneakers GUANGZHOU ANAX FASHION SHOES LIMITED , https://www.gzanaxleathershoes.com
Several installation methods of wall glass decorative mirror